EDWARDS IPX 100 Products

  • EDWARDS: iPX 100

    Details
    ID#:
    137641
    Category:
    Pumps
    Dry pumps, many available.
  • EDWARDS: iPX 100

    Details
    ID#:
    9068847
    Category:
    Pumps
    Pump.
  • EDWARDS: iPX 100

    Details
    ID#:
    54017
    Category:
    Pumps
    Pumps.
  • EDWARDS: iPX 100

    Details
    ID#:
    9028253
    Category:
    Pumps
    Pump.
  • EDWARDS: Diffstak 100 / 300P

    Details
    ID#:
    137250
    Category:
    Pumps
    Diffusion pump | Pneumatically actuated high vacuum valve | Water-cooled | N2 pumping speed: 280L/sec | ISO 100 inlet | NW25 backing connection | Power requirements: 210-225VAC, 50/60Hz.
  • EDWARDS: iPX 100A

    Details
    ID#:
    9063152
    Category:
    Pumps
    Dry pumps.
  • EDWARDS: IGX3 / 100

    Details
    ID#:
    138524
    Category:
    Pumps
    Dry booster pump with roots pump packages | Voltage: 200-230 V.
  • EDWARDS: iPX 100A

    Details
    ID#:
    122609
    Category:
    Pumps
    Pump, 208V, 59 cfm.
  • EDWARDS: iPX 180A

    Details
    ID#:
    9069256
    Category:
    Pumps
    Dry pumps.
  • EDWARDS: iPX 500A

    Details
    ID#:
    9012919
    Category:
    Pumps
    Dry pumps with bellows.
  • EDWARDS: EXT 100 / 300

    Details
    ID#:
    117748
    Category:
    Pumps
    turbo pump.
  • EDWARDS: iPX 500A

    Details
    ID#:
    9020154
    Category:
    Pumps
    Dry pump, 400 V.
  • EDWARDS: iPX 180

    Details
    ID#:
    181615
    Category:
    Pumps
    Pump.
  • BOC EDWARDS: Chemprep 100

    Details
    ID#:
    175033
    Category:
    Pumps
    Chemical blending module.
  • EDWARDS: 4080+

    Details
    ID#:
    9020216
    Category:
    Chillers - Recircul...
    Chillers | | Performance (nominal): | Temperature range: -40°C to +80°C in 0.1°C increments | Cooling capacity: 700 W @ -40°C / 2400 W @ -20°C to +80°C | Heating capacity: 2250 W | Temperature stability: Coolant temperature control within 1.0°C of set point | Temperature ramp: +25°C to +80°C < 25 minutes | (no load): +25°C to -30°C < 15 minutes | Pump capacity: 3 gpm flow at 20°C at 60 psi, up to 100 psi system pressure | | Refrigeration system: | Refrigerant: HFC R404A | Compressor: 2.8 kW, 3 phase hermitically sealed | Heat exchanger: high efficiency cross flow plate | | Coolant circulation system: | Coolant fluid: perfluorocarbon coolant 3M FC-77, 3M FC-3283, 3M FC-8270, 3M HFE 7500, or Ausimont Galden HT110 | Pump: magnetic drive gear pump, 3/4 HP motor.
  • EDWARDS: E306

    Details
    ID#:
    94348
    Category:
    Evaporators
    Vacuum evaporator with pumps and fixturing | Unit has bell jar with multiple feed throughs and rotation | Diffusion pumped with EDWARDS 2-stage backing pump | Unit was previously used for doing Cr/Au or Ni-Cr/Au | System's thermal source inputs were modified and hooked up with a heavy ARC welder power supply for lots of power | Jar is cracked.
  • BOC EDWARDS: Auto 500

    Details
    ID#:
    9073803
    Category:
    Evaporators
    Thermal Resistance Evaporator Coater | Turbo Pump: Edwards EXT 255H / ISO 100K, P/N: B75301000S | Turbo Pump Controller: Edwards EXC 300 | Foreline Trap: Edwards FL20K | Vacuum Valve: Edwards PV25EKA | Rotary Vane Vacuum Pump: Edwards RV12 | Source Controls: (2) Dual Edwards Thyristor | Controller Modules: (2) Dual Edwards LT/HT with LT Transformer and HT Power Supply | Bell Jar: not included.
  • EDWARDS: E2M40 / EH500

    Details
    ID#:
    137284
    Category:
    Pumps
    Pump package | E2M40 roughing pump, 2-stage, 80 cfm | EH500 blower, 300 cfm | Ultimate pressure: 1.1 x 10^-4 Torr | ISO 100 inlet.
  • EDWARDS: 3000 E

    Details
    ID#:
    159100
    Category:
    Leak Detectors
    Helium leak detector | Includes (2) Edwards vacuum pumps (28 m3/hr) | Unit was shut down Q2 2011.
  • EDWARDS: iH1800 HTX

    Details
    ID#:
    152261
    Category:
    Pumps
    Pump | Specifications: | Typical peak pumping speed: | m3/h: 1800 | cfm: 1060 | l/m: 30006 | Typical ultimate vacuum 60Hz (with shaft-seals purge only for iH): | mbar: 1.E-03 | Torr: 8.E-04 | Inlet Connection: ISO 160 bolted | Outlet Connection (iH pumps exhaust line must be metal for 2m): NW40 | Noise level (measured at I meter form the pump): dB(A): <69 | Nitrogen Supply Pressure: | Flow rates (with nitrogen supply capacity of 100 slm): psig: 20~100 | Nitrogen Flow (Low/ Light): slm: 4 | Nitrogen Flow (Med.): slm: 14 | Nitrogen Flow (Med+Exh): slm: 19 | Nitrogen Flow (High/ Harsh): slm: 44 | Nitrogen connector: 1/4" Swagelok | Cooling-water Connectors (Quick-release connectors (pair) thread size 3/8" BSP): Supplied | Water supply pressure: psig: <100 | Typical pressure differential across supply and return with flow of 7 l min-1: psig: 15 | Supply temperature: °C: 20 | Minimum flow rate required for reliable drypump system operation: l/min: 4 | Mains supply connector: Harting HAN-K-4/2 | Supply voltage: 200~230V, 380~460V 60 Hz | Phase: 60Hz, 3-phase | Motor rating: kW: 7.0 | Max Amps (FLA) Full Load Current (A) - Low voltage: A: 29.8 | Max Amps (FLA) Full Load Current (A) - High voltage: A: 14.4 | Power at ultimate vacuum: kW: 4.1 | Current at ultimate vacuum - Low voltage: A: 17.3 | Current at ultimate vacuum - High voltage: A: 10.4 | Fit a secondary earth: must fit | Crated.
Copyright © 2011 Capital Asset Exchange & Trading LLC. All rights reserved.